Making water based Injectable Winstrol???

[Swoleburn]

Ok, Im trying to make some Waterbased Winstrol (winny) and not sure what I need. I dont want to make oil based Winstrol (winny) for fear of people thinking its fake. So in other words it needs to look like the classic milky winstrol. If anyone could help me out it would be greatly appreciated. Thanks.
Swoleburn

 

[Amateur]

Read the stickies

Water Based Winny
This hormone has a screaming high melting point. For this conversion solvents will be used to bring the stanozolol into a clear solution for filtering and titration. The final result will be a suspension.

Items needed for a 1 gram conversion:

1 Gram Winstrol (winny) powder
4.0cc PEG 300/400
0.45um syringe filter (2 quantity)
0.6ml polysorbate 80
0.4ml benzyl alcohol
14.25ml distilled water
Beaker
20ml vial
20g pins
5ml syringe
10ml syringe
Mix 14.25ml of distilled water with 0.4ml benzyl alcohol.
Pass through syringe filter into 20ml vial.
Put 2ml PEG300/400 into beaker and add 0.6ml of polysorbate 80.
Add 1 gram of stanozolol powder to PEG/ps80 mix.
Heat until stanozolol clears. The heat will be very high, PEG may smoke. This is ok.
Allow stan liquid to cool.
Draw into 5ml syringe, run it through the second new syringe into the 20ml vial containing our steralized water.
NOTE: You can use the same syringe filter as long as the filter is completely dry.
As you filter the PEG/ps80/Stanozolol mix through the filter into the water it will titrate back into micronized form in the water. When this is done shake vigerously.
Run 2 more ml's of PEG300/400 through filter to purge.
This conversion results in 20ml - 50mg/ml sterile water based stanozolol suspension for injection.

Additional Note: After much experimentation I have found that ps80 is NOT needed. However, I have a contact who makes large volumes of this, and has found that about 1 out of 10 conversions will clump for some reason. Adding ps80 alleviates the problem, so to avoid this I have included it in the directions.

 

[bmass]

Winny Suspension in Water using NO PEG and NO crashing during Filtering!

--------------------------------------------------------------------------------

This has worked for me several times now. Please follow the directions carefully and do not try to make 50mL or 100mL at a time. It will not work with this formula.


----How to make Winstrol Suspension @ 100mg/mL X 20mL in WATER using NO PEG and NO crashing during filtering!---

-2 grams stanozolol powder X 0.75 displacement volume = 1.5mL
-24% BB = 4.8mL
-3% BA = 0.6mL
- 3% Polysorbate 80 = 0.6mL
-DISTILLED Water (ONLY use Distilled Water!) 12.5mL

Procedures:
-Combine stanozolol powder, BA, BB, PS80 and heat until clear while swirling.
-Sterile filter this hormone concentrate into your sterile vials **You should NOT have to filter fast. Let the solution cool until its warm, it should not crash!
-Using a NEW filter, filter in your Distilled water at any pace you like. Be sure to keep swirling the vial as you filter in the distilled water.

*SHAKE the hell out of your Winny.

Complete! You now have Winstrol (winny) @ 100mg/mL X 20mL.

Good luck!
*Feel free to share this with your homies!

Diablo

--------------------------------------------------------------------------------

 

[DocJ]

Both those will work well. I've found all the PEG does is help make sure the pin doesn't clog when injecting. However, there's some speculation that PEG could interfere with absorption at the injection site but I believe it's not a factor with a suspension. I'd never use PEG by itself as a carrier or with an oil based preparation. If your buddies are just going to use "normal" sized pins (i.e. not insulin pins), I'd use the non-PEG recipe.

 

[zaqwe]

This is a 2006 post!

I used to have a lab, and wini is by far the most difficult substance to produce. To start with, you can not filter stanozolol, so imagine how difficult it is to sterilize that. And mixing it with water you need expensive equipment.

This is why we see that oil garbage so often!