Home brewing Trestolone acetate (MENT).Please advice.

[danielbiker]

Hi Guys , I Need some help with brewing Ment for my research project.I read almost everything is available on the internet about this compound and I was looking for a while to get some for my research project. Fortunatly I found Purity and as you know they have this stuff for research purpose. I never brew the gear before but I have to do it this time. I have done some research on home brewing but I have a lot to learn so please don't be too tough on me if I say something stupid . I'm planning to do it at 100mg/ml, so one vial from Purity (1gram of powder) and 10 ml of BB and oil will get me to that. What I have to do is add 2ml of BB in the vial then add 0.2 ml of BA and 8ml of grapeseed oil. I found a site that sells this stuff for labs and the oil is already filtered. My question is how long do I have to"cook" it in the oven and what temperature to get it melted. Purity site says MENT is dissolving in oil but I know melting and dissolving is not the same thing .The last step will be to sterilized it. Is ok to keep it in the oven for 25-30 minutes at 250 degrees F. Thanks guys. I really appreciate your help.

Respect, Daniel.

 

[Ligand]

Hey bro,

You don't really need to "cook" it per se. The temperature at which it melts depends on different factors of the compound itself. Usually you can find the melting point of a compound online but I can't seem to find trestolone anywhere. I'll tell you how I normally melt my gear and you can decide if you want to do that or another way.

What I do is put my oil, BB, BA, and powder in a beaker and put a pot of water on the stove until boiling. Then I take the pot off the heating element and place my mixture of liquids in the boiling water (obviously do not pour it out, just dunk the beaker/mason jar in the water) and leave it in there for a couple seconds and then take it out. (you might want to use gloves or a heating pad to hold your jar). Put the pot back on the stove and let it get to a boil again. I repeat the above process until the powder is completely melted and the oil is clear, then push it through a filter into a vial and its good to go at this point.

You can try that or you may want to try to put it in the oven for a little bit. I prefer the stovetop method because its a bit more involved and there isn't a lot of waiting. Just make sure the powder is completely melted and you should be ready to go.

Good luck

 

[danielbiker]

Thanks,man .Iappreciate your advice.

Hey bro,

You don't really need to "cook" it per se. The temperature at which it melts depends on different factors of the compound itself. Usually you can find the melting point of a compound online but I can't seem to find trestolone anywhere. I'll tell you how I normally melt my gear and you can decide if you want to do that or another way.

What I do is put my oil, BB, BA, and powder in a beaker and put a pot of water on the stove until boiling. Then I take the pot off the heating element and place my mixture of liquids in the boiling water (obviously do not pour it out, just dunk the beaker/mason jar in the water) and leave it in there for a couple seconds and then take it out. (you might want to use gloves or a heating pad to hold your jar). Put the pot back on the stove and let it get to a boil again. I repeat the above process until the powder is completely melted and the oil is clear, then push it through a filter into a vial and its good to go at this point.

You can try that or you may want to try to put it in the oven for a little bit. I prefer the stovetop method because its a bit more involved and there isn't a lot of waiting. Just make sure the powder is completely melted and you should be ready to go.

Good luck

 

[Stone]

And consider yourself lucky you have a MENT powder source!!!