pinning two shots in one syringe

[akka]

this is probably a really stupid issue but whatever. so im doing a deca and test cycle and i wanted to mix the test and deca together in one syringe and shoot it together. but the problem is i just seem to be incapable of drawing it properly. when i draw any gear into the syringe its terrible, its not a smooth draw at all, i get air bubbles and can't tell how much i've drawn in properly until i tap it and get all the air out... so i always have to push excess back into the vial or suck more in.
so if i tried pulling deca in once ive got my test in the syringe then i'd be all over the place with my doses and probably be putting test into the deca.
im rambling a bit but its hard to articulate what i mean. so i guess im just asking if anyone else has any problems drawing? any tips? links to videos?
i use a 21g to draw and i fill up the syringe with air and then expel it into the syringe before i draw as well. i dunno why i f*ck it up so bad

 

[Greazy-Pickle]

bro.. your way over doing it.. 1st of all your dosages dont need to be that exact.. just draw as close to 1cc as you can then do the same on the next vial.. and you dont have to get every last bubble out of the syringe.. your not shooting heroin..

 

[Bullseye Forever]

i would draw my test out first,then the deca,ever how much test you are using,assuming you are pinning 2 times per week,say you are using 500mg of test /week,just insert your needle with the amount of air in cc's,say its 250mg/ml test,push a cc of air into your vial,then draw it out,then do the same with the deca,just count the lines on the syringe and push that much air into the vial and draw your deca out,works well for me.....now i might get bashed for explaining it like that lol,but thats how it works best for me lol..good luck man

 

[UserAt204]

Get some 18g pins and leave one in each vial then attach the syringe barrel and draw out desired amount. Comes out very easy. Or use two pins.

 

[Bullseye Forever]

Get some 18g pins and leave one in each vial then attach the syringe barrel and draw out desired amount. Comes out very easy. Or use two pins.

brother you explain stuff so much better than anyone and its simple to understand,unlike me lol....you da man!!

 

[coltmc45]

Make sure your pushing air into your vial before you draw out. Creates pressure in the vial and makes the draw very easy. Also draw back very slowly especially on your test since I'm assuming it's test c or e and oil based. You can even try pushing 2 cc's of air into your vial. Your syringe will pretty much fill itself. Just be careful when u do that so you don't waste your gear and pull your plunger back at the same time you pull your syringe out the vial. Then next time you pin just push 1 cc of air in since there's still pressure in the vial. Dunno if that makes sense or helps but that's what I do.

 

[UserAt204]

With an 18g pin you don't need to add air or anything simply draw out and attach pin for injecting. Why mess with anything else when it's so simple. You can get 25 18g pins online for about $3.

 

[akka]

thanks guys... as i said in the opening post yes i do push air in before i draw, but i think ill try drawing more slowly, i do draw quickly i spose. if that doesn't work then ill get the 18's.
cheers.

 

[tgerm]

i would draw my test out first,then the deca,ever how much test you are using,assuming you are pinning 2 times per week,say you are using 500mg of test /week,just insert your needle with the amount of air in cc's,say its 250mg/ml test,push a cc of air into your vial,then draw it out,then do the same with the deca,just count the lines on the syringe and push that much air into the vial and draw your deca out,works well for me.....now i might get bashed for explaining it like that lol,but thats how it works best for me lol..good luck man

Just my opinion but I would draw 2 cc air into the syringe. Then put 1cc into the deca bottle, remove the needle and put the other cc in the test. Then draw the test and remove the air so you have exactly 1 cc. Then when you stick the deca again it already has air in it so no need to try to push air in the deca with a syringe full of test.

 

[Bullseye Forever]

Just my opinion but I would draw 2 cc air into the syringe. Then put 1cc into the deca bottle, remove the needle and put the other cc in the test. Then draw the test and remove the air so you have exactly 1 cc. Then when you stick the deca again it already has air in it so no need to try to push air in the deca with a syringe full of test.

ah ok,gotcha bro.....seems so much better that way,thanks

 

[stiphy]

Just my opinion but I would draw 2 cc air into the syringe. Then put 1cc into the deca bottle, remove the needle and put the other cc in the test. Then draw the test and remove the air so you have exactly 1 cc. Then when you stick the deca again it already has air in it so no need to try to push air in the deca with a syringe full of test.

This^. You may also want to change needles before injecting because needles will dull after repeated vial insertions.

 

[tgerm]

This^. You may also want to change needles before injecting because needles will dull after repeated vial insertions.

This. I change the needle even after 1 push through the stopper. I've seen microscope pics of needles after just one stick. Not pretty.

Can't embed this pic cuz it's blocked on this comp.
syringe microscope - Bing Images

 

[tailhold]

Get some 18g pins and leave one in each vial then attach the syringe barrel and draw out desired amount. Comes out very easy. Or use two pins.

Are you advising him to leave a 18g pin in the vial for future use?