What is wrong with my cyp? Its hardening into a jelly!

[kev ute]

Please, a little help here would be appreciated. My bottle of cyp over the last 4 days seems to be hardening into a jelly. What is happening, or what is wrong?

4 days ago took a shot and the bottle was totally fine as far as i remember. Then went to shoot today and it seemed to be developing into a jelly at the bottom. I shook it up and that didn't seem to have any effect.

Is it possible that where i keep the vial is too cold?

What can i do to fix this? Does it just need to be heated up? I'd like to know before i just start trying to fix this. What would be the proper way to heat it up?

I've finished one bottle and had no problems and i've been getting fantastic results so far. This bottle i just started and now this is happening. I don't want to have to waste a bottle.

Any and all info and input is totally appreciated.

 

[blazeftp]

Is it like a white mist ?

 

[82nd_Fister]

You dun goof'd, cuzzzz.

 

[kev ute]

Is it like a white mist ?

No its not like a mist at all. The color is staying the same, its just jellifying.

Whats your thoughts? does it just need to b heated possibly?

 

[kev ute]

You dun goof'd, cuzzzz.

What do you mean that its goofed? Any reason as to why and or how?

What do you think is wrong/happening to it?

 

[ezred]

chances are it is just crashing, heated it will probably return it to its state. if you're worried about it, bake it, though i doubt that would be necessary. but i'm a newb so wait till someone who actually knows their left nut from their right to chime in.

 

[kev ute]

chances are it is just crashing, heated it will probably return it to its state. if you're worried about it, bake it, though i doubt that would be necessary. but i'm a newb so wait till someone who actually knows their left nut from their right to chime in.

What does it mean if its crashing? And why would it do that?

 

[Jose33]

What does it mean if its crashing? And why would it do that?

crashing can occur for a number of reasons. Mostly chemical ratios are off or the amount of chemicals added was not enough to dissolve the powder completely. Were getting into the colder months so youll see more crashes.

heating it before injection is usually what i do, however if you have a good domestic source you may be able to get a replacement. If its international i dont think you wanna do that and just use the heating method.

 

[Mr. Humdiddly]

What is the vial size dose etc? Are you seeing crystals forming in the bottom or is is more like a paste?

If it is crrystals add 1ml of BA give it a good shake and put it in the oven at 175 degrees for 45 min. No need to vent it at this temp.

If it is paste like that would constitute use of a low temp oil base. Try heating it up in a bowl of warm tap water. If that does not work you may have got some oil going rancid. It is rare but, I have seen it happen. Draw some of the sludge up and smell it. If it is sweet dump the vial.

 

[Die$eL~Man]

where are you storing your gear ?

 

[kev ute]

What is the vial size dose etc? Are you seeing crystals forming in the bottom or is is more like a paste?

If it is crrystals add 1ml of BA give it a good shake and put it in the oven at 175 degrees for 45 min. No need to vent it at this temp.

If it is paste like that would constitute use of a low temp oil base. Try heating it up in a bowl of warm tap water. If that does not work you may have got some oil going rancid. It is rare but, I have seen it happen. Draw some of the sludge up and smell it. If it is sweet dump the vial.

Its a 10 ml vial @ 300mg/ml. I've just been leaving it in my room. I'll admit that the room is a little on the cold side.

Earlier today i just warmed it using body heat. I sat on the vial and it turned back into a full liquid. So that made me happy.

Hopefully i can just simply heat it before shots. But thanks for all the info.

Just curiosity, i could put the whole vial into the oven. and what does this do to it?

 

[Jose33]

Its a 10 ml vial @ 300mg/ml. I've just been leaving it in my room. I'll admit that the room is a little on the cold side.

Earlier today i just warmed it using body heat. I sat on the vial and it turned back into a full liquid. So that made me happy.

Hopefully i can just simply heat it before shots. But thanks for all the info.

Just curiosity, i could put the whole vial into the oven. and what does this do to it?

I would just put a pan on the stove on medium heat, put the vial in on the stove in a pan, stirring it every so often and let the oil heat up. Doesnt need to go into the oven.

Baking it in the oven will kill all the bacteria (if any is present) in the vial if it is done properly. I dont think this is required for what your needs.

 

[Mr. Humdiddly]

Its a 10 ml vial @ 300mg/ml. I've just been leaving it in my room. I'll admit that the room is a little on the cold side.

Earlier today i just warmed it using body heat. I sat on the vial and it turned back into a full liquid. So that made me happy.

Hopefully i can just simply heat it before shots. But thanks for all the info.

Just curiosity, i could put the whole vial into the oven. and what does this do to it?

DO NOT use a high heat source such as the oven. You have an oil carrier that has a high lipid concentration. That means the smoke point is significantly lower. Just heat it up with warm tap water. Make sure to clean it with alcohol before drawing. If you can turn the heat up in your room this will keep it from going back to a semi solid state.

 

[XxDannyxX]

You dun goof'd, cuzzzz.

strong miscer