winsrol oil base
- Thread starter ROIDRAGER
- Start date
Billy_Bathgate
Community Veteran, Chemistry Guru
yes, no
its not the best in oil, but check out basskillers site. he has a nice recipie for it. it would be easier in a PEG of glycerin base
its not the best in oil, but check out basskillers site. he has a nice recipie for it. it would be easier in a PEG of glycerin base
Praetorian
New member
Injectable Winny in oil!
How To Make Injectable Winstrol In Oil
How To Make Injectable Winstrol In Oil
Last edited:
Praetorian
New member
cont.
1) Weigh out 1 gram of winstrol powder, you will need a scale (I got mine here http://under-50.balances.com/) use the tare function to take away the weight of the container that holds your powder, and weigh it out to 1 gram.
2)Draw out 2 ml of the super solvent, using 1 of the 3 ml syringes.
3)Place the powder in the open glass vial, then add the super solvent to the powder in the vial
Step 4
A:
Place back on rubber stopper, put one of the 20g pins in the stopper. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat until powder disolves into a liquid (the melting point of winstrol is between 239.8-242 degrees F). Turn off heat, and let it cool down still in the pan, until it reaches room temp. again takes about 15 minutes.
Vial will be VERY HOT, so use an oven mit.
B:
Also heat seseame oil (heat more than 17ml because you won't get it all out) it can be heated on a stove eye, or in the oven, I heated mine in the oven in a muffin pan, the oil needs to reach 212 F., to help sterilize the oil. I put mine in the oven at 275 F. Just to make sure.
Step 5
Draw out .2 ml of benzyl alcohol, this is 1% of the final solution. It is very important that you do not use more than 1% of the solution with winstrol, or it could crash when finished.
Step 6
Add BA to the solution in the vial. Shake very gently.
Step 7a
Draw out the oil with the 10 ml syringe, (Be sure you have allowed it to cool down some) add the 15ml of oil to the solution. Shake very gently again.
**Note - After adding the oil to the solution the winstrol may begin to clump up back into a powder, if it does, you just need to reheat it again like in Step 4a, remember to let it cool slowly. My powder did this, and this took care of it.**
Step 7b
Save 2 ml of oil in the syringe, and re-cap it. You need this later during the sterile filter process to make sure none of the winstrol is left in the filter.
Step 8
Place 1 of the 18 guage pins in the steile unopened vial, and attach the whatman sterile filter.
Draw out the solution using the other 10ml syringe, attach to the filter, and slowly press solution into the sterile vial.
Then use the remainding 2ml of oil in the other syringe, to run through the filter, to make sure that none of the winstrol is left in the filter.
Step 9
After filtering, leave the pin in the sterile vial, remove the filter. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat solution for about 15 to 20 minutes. Turn off heat, and let it cool down still in the pan, until it reaches room temp. again this takes about 15 minutes.
Enjoy!
P
1) Weigh out 1 gram of winstrol powder, you will need a scale (I got mine here http://under-50.balances.com/) use the tare function to take away the weight of the container that holds your powder, and weigh it out to 1 gram.
2)Draw out 2 ml of the super solvent, using 1 of the 3 ml syringes.
3)Place the powder in the open glass vial, then add the super solvent to the powder in the vial
Step 4
A:
Place back on rubber stopper, put one of the 20g pins in the stopper. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat until powder disolves into a liquid (the melting point of winstrol is between 239.8-242 degrees F). Turn off heat, and let it cool down still in the pan, until it reaches room temp. again takes about 15 minutes.
Vial will be VERY HOT, so use an oven mit.
B:
Also heat seseame oil (heat more than 17ml because you won't get it all out) it can be heated on a stove eye, or in the oven, I heated mine in the oven in a muffin pan, the oil needs to reach 212 F., to help sterilize the oil. I put mine in the oven at 275 F. Just to make sure.
Step 5
Draw out .2 ml of benzyl alcohol, this is 1% of the final solution. It is very important that you do not use more than 1% of the solution with winstrol, or it could crash when finished.
Step 6
Add BA to the solution in the vial. Shake very gently.
Step 7a
Draw out the oil with the 10 ml syringe, (Be sure you have allowed it to cool down some) add the 15ml of oil to the solution. Shake very gently again.
**Note - After adding the oil to the solution the winstrol may begin to clump up back into a powder, if it does, you just need to reheat it again like in Step 4a, remember to let it cool slowly. My powder did this, and this took care of it.**
Step 7b
Save 2 ml of oil in the syringe, and re-cap it. You need this later during the sterile filter process to make sure none of the winstrol is left in the filter.
Step 8
Place 1 of the 18 guage pins in the steile unopened vial, and attach the whatman sterile filter.
Draw out the solution using the other 10ml syringe, attach to the filter, and slowly press solution into the sterile vial.
Then use the remainding 2ml of oil in the other syringe, to run through the filter, to make sure that none of the winstrol is left in the filter.
Step 9
After filtering, leave the pin in the sterile vial, remove the filter. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat solution for about 15 to 20 minutes. Turn off heat, and let it cool down still in the pan, until it reaches room temp. again this takes about 15 minutes.
Enjoy!
P
SupermanQC
Hero Of the Day
Neet , Thx man 
Similar threads
