Am i doing something wrong or are these syringes complete shit ?

[t6100]

I bought some 'Muzamedical' syringes and needles and have nothing but trouble and annoyance with them as they've caused me to lose some oil due to their completely shit quality.

About 1ml of oil stays stuck in the end ( the tip ) of the syringe after each injection and theres nothing you can do to push it out of this space at all. The arrow on pic points to this 'dead space'
View attachment 547728

The needles are 27g 1 1/4 and its harder to push oil through these than 29g slin pins.
I'm injecting into delt and then half way through the injection it just stops pushing the oil through, and some blood comes back into the syringe.. how is this even possible ?!

Do you think i should throw away the syringes AND needles and just get some terumo 25g 1"ers and syringes ?
Or just buy some 25g 1" needles, because the amount of pressure required to push the thin prop oil out of these 27gs is just stupid, and can't be good for the muscle as i heard it causes displacement.

Thanks

 

[hijacked]

I bought some 'Muzamedical' syringes and needles and have nothing but trouble and annoyance with them as they've caused me to lose some oil due to their completely shit quality.

About 1ml of oil stays stuck in the end ( the tip ) of the syringe after each injection and theres nothing you can do to push it out of this space at all. The arrow on pic points to this 'dead space'
View attachment 547728

The needles are 27g 1 1/4 and its harder to push oil through these than 29g slin pins.
I'm injecting into delt and then half way through the injection it just stops pushing the oil through, and some blood comes back into the syringe.. how is this even possible ?!

Do you think i should throw away the syringes AND needles and just get some terumo 25g 1"ers and syringes ?
Or just buy some 25g 1" needles, because the amount of pressure required to push the thin prop oil out of these 27gs is just stupid, and can't be good for the muscle as i heard it causes displacement.

Thanks

Cmon man, 1cc? Thats a lot! Are you sure 1cc is getting trapped in the end? If thats the case i would throw those fucking things away. But i think you are mistaken, it cant be that much.
How big is the barrel? When a syringe is hard to push, its a combination of the needle size, and the size of the plunger. For example, you can use a 29g, 1cc slin pin, and inject your oil no problem. The needle is small, but the surface area of the plunger is small too. If you tried to put that needle on a 3cc barrel, it would be very hard to push.
If i were you, i would either get the terumo 3cc syringes with the 25g x 1" pins that you mentioned. Or if you want to inject with a smaller needle, then just use a 1cc slin pin. You wiil have to heat your oils to make it thin enough to withdraw. And you will have to stick with delt and pec injects. Im assuming you are lean enough for slin pins too. Remember, the slin pin is only 1/2" long, so you have to inject where the muscle is close.

 

[NightRaidsONLY]

Yeah man its pretty clear that you are mistaken. If you lost a whole mil/ 1cc per pinn youd lose half ur gear. Haha. And 1/4 isnt long enough bro. Just get urself some 25g 1"needle pins and rock it out. You will have no problems. I hit quads and delts with em for 12u weeks trouble free. And be sure u warm the oil

 

[t6100]

Cmon man, 1cc? Thats a lot! Are you sure 1cc is getting trapped in the end? If thats the case i would throw those fucking things away. But i think you are mistaken, it cant be that much.
How big is the barrel? When a syringe is hard to push, its a combination of the needle size, and the size of the plunger. For example, you can use a 29g, 1cc slin pin, and inject your oil no problem. The needle is small, but the surface area of the plunger is small too. If you tried to put that needle on a 3cc barrel, it would be very hard to push.
If i were you, i would either get the terumo 3cc syringes with the 25g x 1" pins that you mentioned. Or if you want to inject with a smaller needle, then just use a 1cc slin pin. You wiil have to heat your oils to make it thin enough to withdraw. And you will have to stick with delt and pec injects. Im assuming you are lean enough for slin pins too. Remember, the slin pin is only 1/2" long, so you have to inject where the muscle is close.

Yeah the thing is i'm using prop for testosterone replacement therapy (TRT) so 50mg EOD and it's been working better than cyp and enanthate. But because of EOD injects I can't keep doing delts and so need to do quads as well, but i feel the 0.5" doesn't go deep enough as i have bad PIP wherever i inject because i feel pain all around the muscle for days after so either the oil is leaking or the large amount of pressure im applying to the syringe is causing muscle tissue displacement.

 

[t6100]

Yeah man its pretty clear that you are mistaken. If you lost a whole mil/ 1cc per pinn youd lose half ur gear. Haha. And 1/4 isnt long enough bro. Just get urself some 25g 1"needle pins and rock it out. You will have no problems. I hit quads and delts with em for 12u weeks trouble free. And be sure u warm the oil

there seems to be some confusion regarding units of measurment.
0.1Millileters ..( not 10Millileters ) is being lost in the syringe.

 

[NightRaidsONLY]

there seems to be some confusion regarding units of measurment.
0.1Millileters ..( not 10Millileters ) is being lost in the syringe.

Missed the decimal point. Anyways...i honestly feel with soem 25 g 1" pins youll be cruisin. You can blasr quads and delt and just keep alternating. A heating pad on the quad for a.couple mins before injecting. And lay ur filled syringe in the heating pad till its nice and warm. Youll notice a HUGE differsnce. U can even keep the heat pad on it for a few minutes after pinning. It helps trust me.

 

[NightRaidsONLY]

Also...try drawing in a small airbubble and having it between ur gear and the plunger. As u get to the last .01ml the air will displace any gear left in the flash chamber or needle nicely.

 

[t6100]

Ok thanks for the advice, you think i should throw out the syringes or just just replace the needles with 25guagers ?

 

[NightRaidsONLY]

Throw em out bud. Shits cheap. Spend 20bucks at bulksyringes.com or somehwere comparable.

 

[BigKevKris]

directlinemedical FTW

 

[TheFitnessLife4ever]

It's normal to lose .1cc per inj. Just add about .2cc of air, and there will be no oil wasted. And yes, it's safe to inject air in the muscle. I've used this technique ever since I can remember(just be sure to aspirate every time otherwise you very well might fuck yourself up).

 

[old&stacked]

While a little expensive I go to walgreens they r .25 per and they are quality with screw on needles and thus fa I have no complaints about them. Remeber that this is the equipment u r using to introduce gear to your body. Would u like your doc to use crappy below standard equipment to take care of u. Then why r u going to do that to yourself.