How can I make Test400 thinner so it doesnt take so long to inject??

[Oneil12345]

Hi im new to this forum. Im 6'0 193pounds 23years old and i just purchased some test400. When i went to inject, everything went fine but it took more than 5 minutes to get 1ml in and thats a little bit to long for me. Ive done Winstrol (winny) and tren A injects before and it only took a couple seconds i was wondering how i can make this test400 thinner so i dont have to stand their with it in my arm for longer than 5 minutes. thanks

 

[fishfreak]

Are you taking the T400 by itself, or stacking it with a good anabolic like eq or Winstrol (winny) ? If so, combine the 2 substances in the syringe & hit the outer quad or glutes.

 

[Oneil12345]

test400

hey ya im taking Winstrol (winny) tabs not inject. So yes t400 by itself but it says on vial its mixed with cottonseed oil but i mean its still like syrup im not to keen on needles i mean i had no problem taking Winstrol (winny) and tren injects a year ago becuase it was in and out but the t400 is rediculous.

 

[zedhed]

Heat that shit up, will help some. If you dilute it to make it thinner then you dont T400 any more.
If you dilute it and then can do the math to make up for the dilution you can get the same amount.
Dont know if youre realdy for that yet tho.

 

[Oneil12345]

yea i dont know if im ready to be screwing around with it like that yet dont know enough about that procedure. But how would you go about heating it up like placing vial in hot water??

 

[bombom]

in oven to powder melting point..

 

[koi]

I'm currently using Testoviron by Bayer. It's a very thick oil also.

I heat the vials up in warm water for drawing and then I use a hair dryer to heat the syringe up before injecting. It goes in a lot easier warm.

HTH,
Koi.

 

[RJ]

in oven to powder melting point..

damn you're advice sucks so far. lol

OP - just fill up a thing of tupperware with water and pop it in the microwave for 2 minutes.

Then take it out and place the vial in the hot ass water for about a minute. Then take it out and draw up your gear. It will thin it out quite a bit.

But just FYI, taking a while to inject gear is much better than fast injects. This helps disperse the gear better throughout the muscle.

When you inject it fast, once the solvents wear off, all your left with is the depot (or crystallized powder) and that is what causes those painful ass lumps.

 

[riprockwell]

Hi im new to this forum. Im 6'0 193pounds 23years old and i just purchased some test400. When i went to inject, everything went fine but it took more than 5 minutes to get 1ml in and thats a little bit to long for me. Ive done Winstrol (winny) and tren A injects before and it only took a couple seconds i was wondering how i can make this test400 thinner so i dont have to stand their with it in my arm for longer than 5 minutes. thanks

Take RJ's advice, however one thing you haven't mentioned is what size of gauge needle you are using. What size you shooting with??

 

[Oneil12345]

drawing with 21 and injecting with 25 is what my guy said to use....

 

[Die$eL~Man]

larger guage pin

 

[ECKSRATED]

drawing with 21 and injecting with 25 is what my guy said to use....

that's why it takes so long cus ur using 25g. Use 22 or 23 for glutes. Much better and smoother I think.

 

[Die$eL~Man]

are you using a drawing needle ? or are you drawing from the same pin you shooting ?

 

[Oneil12345]

ok thanks thats too bad i gotta drive 40 minutes to get new ones

 

[Die$eL~Man]

drive 40 mins ? get them overnighted bro

 

[rocko3927]

use a 22 gauge needle. draw up the pen, run it under {the pen} hot water til warm , then inject.

 

[riprockwell]

drawing with 21 and injecting with 25 is what my guy said to use....

That is one of your problems there as you can see. My gear now is fine to shoot with a 25g pin but some gear I ran in the past (straight syrup) would have to be shot with a 22g or 23g. You should be fine with a 23g. And just have the pins overnighted to your pad.

 

[Oneil12345]

overnighted?? lol i have never heard of anything of this. Free deliverd needles??

 

[RJ]

overnighted?? lol i have never heard of anything of this. Free deliverd needles??

there not free dude. use cheappinz or another site that sells pins. they are super cheap.

as for the 25g pin, you should be fine using that if you heat up your gear. And like i said, especially with high concentrated gear, don't worry about shooting gear slow. Its actually better that way.

I use 25g pins for everything and it has always worked great, even with 500mg/ml test E.

 

[Oneil12345]

ok thanks for the advice ill try heating it up tomorrow.