How To Make Injectable Winstrol In Oil

[grafixLSUalum]

Step-by-Step: How To Make Injectable Winstrol In Oil

Thanks to Harvey Balboner at MM for these awesome pics!

Supplies:
1 Gram winstrol
1 20 ml glass vial or larger
1 20 ml sterile glass vial or larger
1 .45 whatman sterile syringe filter.
2 5 or 10 ml syringes
2 3 ml syringes
3 18 or 20 guage pins
2 22 guage pins
17 ml of seseame seed oil
.2 ml of benzyl alcohol
2 ml of Mr. T super solvent (http://www.finakit.8k.com/index.html) or Animals super solvent (http://www.animalkits.be/)
I am using Mr. T super solvent.

This will make 20ml at 50mg/ml.

Tip: Only try to convert winstrol powder 1 gram at a time, it is very easy to ruin it in the conversion.

 

[grafixLSUalum]

Step 1:

Weigh out 1 gram of winstrol powder, you will need a scale (I got mine here http://under-50.balances.com/) use the tare function to take away the weight of the container that holds your powder, and weigh it out to 1 gram.

 

[grafixLSUalum]

Step 2

Draw out 2 ml of the super solvent, using 1 of the 3 ml syringes.

 

[grafixLSUalum]

Step 3

Place the powder in the open glass vial, then add the super solvent to the powder in the vial.

 

[grafixLSUalum]

Step 4

A:
Place back on rubber stopper, put one of the 20g pins in the stopper. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Cut on heat, heat until powder disolves into a liquid (the melting point of winstrol is between 239.8-242 degrees F). Turn off heat, and let it cool down still in the pan, until it reaches room temp. again takes about 15 minutes.

B:
Also heat seseame oil (heat more than 17ml because you won't get it all out) it can be heated on a stove eye, or in the oven, I heated mine in the oven in a muffin pan, the oil needs to reach 212 F., to help sterilize the oil. I put mine in the oven at 275 F. Just to make sure.

 

[grafixLSUalum]

Step 5

Draw out .2 ml of benzyl alcohol, this is 1% of the final solution. It is very important that you do not use more than 1% of the solution with winstrol, or it could crash when finished.

 

[grafixLSUalum]

Step 6

Add BA to the solution in the vial. Shake very gently.

 

[grafixLSUalum]

Step 7a

Draw out the oil with the 10 ml syringe, (Be sure you have allowed it to cool down some) add the 15ml of oil to the solution. Shake very gently again.

Note - After adding the oil to the solution the winstrol may begin to clump up back into a powder, if it does, you just need to reheat it again like in Step 4a, remember to let it cool slowly. My powder did this, and this took care of it.

 

[grafixLSUalum]

Step 7b

Save 2 ml of oil in the syringe, and re-cap it. You need this later during the sterile filter process to make sure none of the winstrol is left in the filter.

 

[grafixLSUalum]

Step 8

Place 1 of the 18 guage pins in the steile unopened vial, and attach the whatman sterile filter.

Draw out the solution using the other 10ml syringe, attach to the filter, and slowly press solution into the sterile vial.

Then use the remainding 2ml of oil in the other syringe, to run through the filter, to make sure that none of the winstrol is left in the filter.

 

[grafixLSUalum]

Finished Product

Below is what your finished product should look like, it should be a light gold color.

Also I (Harvey Balboner) wanted to thank Basskiller for his help on this.

 

[BiggieSwolls]

Would this method still require the winstrol to be administered ed or eod?

 

[grafixLSUalum]

i believe ED

 

[EQLgearstud]

how hard is it to make compared to Tren?

 

[Doc Banner]

could the same be done with d-bol powder?

 

[grafixLSUalum]

i believe the same could be done with d-bol powder, however, it is easier to just suspend it because you are most likely going to use it orally, or even ethyl alcohol will work as a solvent for d-bol.

 

[muroman]

i am just wondering why go through the trouble to make this shit injectable i have heard that its fine to take oraly. Is it more potent inj or something?

 

[Doc Banner]

I want to make IM d-bol though

 

[basskiller]

i am just wondering why go through the trouble to make this shit injectable i have heard that its fine to take oraly. Is it more potent inj or something?

Because they told me that it couldn't be done.. so I did it!

 

[Jimbo]

I did this and after it set all night with no problems, in the morning it had a bunch of large specks on the bottom of the vial. I heated it until the white specks melted into the solution and it was clear. Since then it has crashed about every 2 or 3 hours. I've re-heated it until it was clear and then the same thing happens. Any suggestions?