Slin pins

[timbo357]

So I've been seeing guys saying they use slin pins for there oils I've always used 25g 1 1\2in I've never seen a slin pin at over 3\4in and attached to a 1ml syringe what are the sizes of these slin pins and syringes your using and where are y'all getting them from?

 

[MeatHead96]

I use 29g .5'' slins for all my injects. Shoot in front delts/side delts/traps. These are lean areas for me. All my bloodwork shows that it works just fine for me and there are many others who do it as well. I heat the syringe with a blow dryer before injecting to make it push through easier. Then leave the pin in for 30 seconds to a minute before pulling it out to make sure no oil leaks out. I'm sure the site sponser carries them.

 

[timbo357]

I doubt I'm lean enough for half an inch I want a inch and a half and what about the syringe? You only inj. 1 ml at a time?

 

[MeatHead96]

I doubt I'm lean enough for half an inch I want a inch and a half and what about the syringe? You only inj. 1 ml at a time?

What is your bf percentage? If you want to use a 1.5" then why did you even post this thread? There are no 1.5" slin pins. Yes I'm on 600mg omnadren and 300mg deca right now and I'm doing EOD injections. I load just a little more than a ml in each pin. When I do short esters I do ED injections. If I get to higher dose cycles in the future I will have to move to a 25g 1" 3cc pin.

 

[timbo357]

I don't know my bf % probably around 18. If you read my post you will answer your own question about why i posted this thread I though perhaps they were using some type of pin that was 29g 1 1-/2 with a 3ml syringe that I had no idea was even made I didn't know what they were talking about that's why I posted this thread hope that helps you

 

[MeatHead96]

I don't know my bf % probably around 18. If you read my post you will answer your own question about why i posted this thread I though perhaps they were using some type of pin that was 29g 1 1-/2 with a 3ml syringe that I had no idea was even made I didn't know what they were talking about that's why I posted this thread hope that helps you

A google search would have told you easily that these do not exist. The whole reason a slin pin works is because the diameter of the barrell is so thin and small that it forces more pressure through to push the oil out. A 3cc barrell would never allow this. Also a 1.5 inch 29g would not be good as it would be much easier to break off into the skin with such a small gauge.

 

[ChrisWho?]

I think the longest needle on a slin pin is .750 or 3/4 Edit-I think it's 5/8" actually.. I hit the same spots as meathead using .5" also with success. I'm running SE also so it's great for ED pinning. You have to back load as there's no way you can draw with a 29g, but injecting with it is fine just takes awhile. But it's well worth it when pinning that much scare tissue wise.

 

[PedestrianX]

Do you guys draw with the slin or backload?

 

[PedestrianX]

oops, missed your post Chris. Thanks

 

[djm6464]

bd and terumo both make 1inch slins.....i do exactly what meathead said.....delts n quads, and because they are so small you can even hit the same areas multiple times, just move over a few inches........delts are my favorite, alot of meat, goes in like a knife through butter

 

[timbo357]

A google search would have told you easily that these do not exist. The whole reason a slin pin works is because the diameter of the barrell is so thin and small that it forces more pressure through to push the oil out. A 3cc barrell would never allow this. Also a 1.5 inch 29g would not be good as it would be much easier to break off into the skin with such a small gauge.

Bro I don't know how else to explain it to you I wasn't sure what people were talking about bc when I searched for them there wasn't anything that was that long I didn't know they were using a regular 1ml .5 in insulin needle i don't know what your problem is with me asking a question that I was unable to find an answer to it's ridiculous I'm having to explain this to you lol meathead

 

[timbo357]

Awesome that's exactly what I was wondering djm I'll have to give those 1in slins a try

 

[UserAt204]

I also do .5 29g in those same areas. Have also hit pecs, bi's, tri's. Works very well. I usually never warm the oil because I use very thin oils but have had to warm a couple different brands.

I personally wouldn't do this with a 1 inch. Seems more likely to break using it IM but they are actually a little tough to break, I have tried.

I back load the pins and if I want to use more than 1ml at a time I use 25g 5/8.

 

[MeatHead96]

Bro I don't know how else to explain it to you I wasn't sure what people were talking about bc when I searched for them there wasn't anything that was that long I didn't know they were using a regular 1ml .5 in insulin needle i don't know what your problem is with me asking a question that I was unable to find an answer to it's ridiculous I'm having to explain this to you lol meathead

Sorry bro I was just in a dickhead mood.