Injection questions before i begin!

[flex90]

hey every1,
I will be starting my Test E/ Tbol cycle in 2 weeks from today.

I will be doing mostly Glute injections with a buddy of mine. ill be usuing a 22 gauge needles 1.5 inches..
If i were to inject my quads can i use same size needle (22gauge, 1.5)?

Another question; can i use the same syringe throughout, and just change needles.. or is it best i use a new syringe everytime i inject?

this is my first injectable cycle, any answers for me?

 

[Ythrashin]

Use a new syringe and needle every time!! I personally use a new fresh needle to inject and one to draw the gear...

You can use the 1.5inch to inject into your quad but only go about 1inch into it.

 

[flex90]

thanks man, rly appreciate it!

 

[Pumpingyork]

Yeh mate u won't to draw with a bigger needle like a 19 g and then change to a smaller one to inject. 22g is pritty big man. I use 25g and just heat up the test in warm water makes it nice and smooth.

Best size for quad would be 23 - 25 g 1 1/4in. Why use a big needle when you dont have to?

 

[tailhold]

I use a new syringe and 2 pins also 1to draw and 1 to inject.

 

[MassMonster86]

i draw with a 22.. shoot with 25g 1 inch everywhere

new syringe new needle every time.

 

[Ythrashin]

Yeh mate u won't to draw with a bigger needle like a 19 g and then change to a smaller one to inject. 22g is pritty big man. I use 25g and just heat up the test in warm water makes it nice and smooth.

Best size for quad would be 23 - 25 g 1 1/4in. Why use a big needle when you dont have to?

I agree with using a smaller gauge needle. I personaly use a 23g to draw and shoot with a 23g or 25g.I did draw gear with a 19 or 20g but ended up with little chunks of rubber stopper in my gear once in a great while...so i now draw with a 23g....

1 1/4 inch is to long for my quads and glutes...
Low BF in those areas... I use 1inch for both quads and glutes.

 

[tailhold]

I use 1 inch 23g for everywhere including draw.

Also when drawing, put the open side of the needle up, long side of the point down as you enter the stopper and the needle will cut through the stopper better and have less of a chance of punching rubber out.

 

[g1234]

Nobody is going to tell you that you can use the same syringe twice. You must use two new pins and a new syringe for each injection, 1 pin to draw and one to inject.

I use 1" 23g for anything (BD blue ones).

 

[KJ_BOSSUTE]

also remember to swab the rubber top of the vial or any bacteria on the stopper will then be in your vial then your glute also remember when you swap tips to push the air out of the syringe

 

[hogman]

syringes are so cheap and easy to get why would you even consider using it twice? A little bit of common since goes a long way! Think about what a Dr office would do and use their methods. Keep it as clean as possible, use rubbing alcohol on the needle, the top of the bottle and on the injection site/you...

cleanliness is next to godlyness

 

[flex90]

alright guys, thanks for all your input!! ... i think i will use maybe a 23-25gauge to inject, and i will stick to 22 to draw so less likely rubber will get in.

one more question .. is a 3ml syringe more convinient than a 1ml... cuz i bought a couple of 1ml's and the plunger will be a bitch to push in considering 1ml fills the whole thing and the plunger is like sticking out alot...?

 

[flex90]

since this is my first time... im trying to make it as practical as possible thx

 

[Flynman]

I made the mistake of re-using a needle and syringe on my very first cycle. It turned out ok....after the hospital put me antibiotics for the infection!! I draw with a 20g and inject with a 23 or 25 gauge. Even if I drop the needle and it touches something I change it for a clean one.

 

[MassMonster86]

i use 3ml syringe.. HOWEVER i full the whole thing up with my stack.

terumo or bd brand

get pinz dot com

 

[amvdub]

alright guys, thanks for all your input!! ... i think i will use maybe a 23-25gauge to inject, and i will stick to 22 to draw so less likely rubber will get in.

one more question .. is a 3ml syringe more convinient than a 1ml... cuz i bought a couple of 1ml's and the plunger will be a bitch to push in considering 1ml fills the whole thing and the plunger is like sticking out alot...?

the 1ml pins are a joke bro. go with the 3ml

 

[flex90]

alright cool

 

[caladin]

i draw with a 22.. shoot with 25g 1 inch everywhere

new syringe new needle every time.

Same as me

 

[ahtwqqaq15]

would 3ml be the same as 3cc?

 

[Ythrashin]

Yes