AML T400 - Crystallized

[stomper69]

Just received my gear the other day and all the T400 was cristallized and still is. What is the best procedure to get it back in oil form to inject . No issues with the Masteron 200.

 

[jonesfarm]

Just received my gear the other day and all the T400 was cristallized and still is. What is the best procedure to get it back in oil form to inject . No issues with the Masteron 200.

Some of test e I got was the same way. I just put the bottle in hot water in a cup. I stop the water about 1/4 inch from the top. After a few minutes it will clear up and I inject it then.

 

[stomper69]

Ok, I will try that out. It was also below 0 degrees out where the gear was sitting until I picked it up.

 

[cthr600]

Usually my tren does this. I hold one end of the vial with a thick bath towel and use a hair dryer to heat the other end and shake every few mins until all crystals are gone. Be careful as it gets pretty warm. Hope this helps.

 

[stomper69]

Tried the hot water... Some of it dissolved but 3/4 of it is still crystals. I will try the hair dryer haha. Once it is dissolved will it stay this way or will it crystallize again after sitting there for a bit.

 

[fancyhuh101]

u may need to use more heat , however , it may uncrystalize but remain foggy . its its foggy its still ok. but u cant take it if its crystallized . place the gear on your coffee makers heating pad if u have one . keep it there until it dissolves . the gear is still good

 

[prnscrn]

Trust has a great thread entitled "How to recover a crashed solution tutorial". It gives a very good explanation about crashed solutions and how to get them back. Try searching for it. I am not sure if I can post the link without breaking rules.

 

[livebigdieyoung]

this has happened to me a few times and i have filled a saucepan with water to about 3 quater the height of the vial, then placed and needle in the vial but above the oil level(this is to let out any pressure) then i heat the vial and every so often swill it around to help to get the crystals to reabsorb!
it has worked every time for me

 

[Patrrickn]

Some prefer the hot water method or heating it on a coffee warmer...I use the oven and set the vials on a pizza pan.... its also easy to control the temp

 

[josephblow]

After mine cleared I mixed it with my tren a so it didn't crash again

 

[ridgeback]

After mine cleared I mixed it with my tren a so it didn't crash again

This is what ya want to do, I divided mine into 2 seperate used empty 10 ml bottles, I then added another 2 ml's of test Prop and 2 ml's of Tren A to them, now I have a beatiful little concoction that makes me feel happy all day long!!

I boiled a cup of water, filled a coffee cup 1/2 way and put the bottle in there for about 5 minutes, crystals will be gone in 5 mins bro!!

 

[stomper69]

So I ended up using a coffee pot warmer and got my gear back to oil. It took about 10 - 15 minutes on the pot to get them fully diluted. Thanks for the help guys ! Now time to grow

 

[stomper69]

Any issues with the gear going bad since I have to re-heat the T400 before every injection since it keeps on re-crystallizing ?

 

[Boh]

I had a similar problem with aml's test cyp. As soon as i took off hieat it went right back to crystallized. I hit up boss and sent a pic and he immediatly sent me a replacement. You should do the same.

 

[stomper69]

Ok I'll have to see what he says since they've had lots of issues with the T400 crystallizing in colder weather. I wasn't aware that it would re-crystallize after diluting it and keeping it in 20+ degree environment. I thought I was g2g after diluting all the vials on the coffee warmer but when I pulled out the gear to start my cycle on Sat. I seen otherwise. I've been putting it in boiling water for 5 minutes prior to injection and it turns back in to oil.

 

[Boh]

Yea i got 8 bottles of cyp and only that 1 was crystalized, it was weird. It clears up but it clouds back in within 10-15 seconds off the heat. mine goes back to crystal way too quick to even shoot, but if iyours goes back to oil long enough to shoot i don't see an issue.

 

[stomper69]

Ya it's goes back and stays to oil for a bit. I haven't left it out on the counter to see how long it takes but as long as I can get it in me I'm rolling!

 

[sadpanda]

happened to me (frozen cuz of canadian weather haha), i just put it in a metal bowl of water and put it on the stove, was perfect after

 

[simplytim]

the oven trick sounds good due to temp control. . what would happen if you left it in boiling water by mistake, or too much heat? will it destroy the gear?

 

[Trust_]

Boiling water is not hot enough to cause any damage to the vial, or whats in it.