Painful post injection!

[aitheanswer2k4]

Ok here the deal;Been injecting Uncles domestic z-line, the problem is the pip (post injection pain) is just way to much! When i did it in my legs almost had to walk on crutches for like 7 days and it took about 10 days for the pain to start going away! I then injected my delts Monday night and it was painless injection but Tuesday the pip wouldn't bad then Wednesday rolled around and omg! it hurt so bad ! Yesterday was def. the worse day though i couldn't lay down or even really put my hand to my side. I really cant take of my shirt because my shoulder hurt so bad and swelling. I'm not worried about the swelling though because thats what happen to my quads. This is my first cycle though. I know it suppose to hurt pretty bad the first time couple of times injecting but i know not this bad,trust me! So another question is i have heard about cutting your gear will like grape seed oil and eo oil, but i heard that the uncle cuts his products with eo oil. I dont know why it would be hurting this bad. I tried all the basic stuff like putting the vial in hot water for about 2 minutes, messaging the area before, and after injection. Also using a hot pad for about 20 minutes post injection. So i would def. appreciate it if someone could help me out. Going to try it in the glutes tonight so we will see how that goes.

 

[h4x0l2]

Sounds like the BA content is very high.


Might want to grab some sterile oil to mix it down with... make sure the measuments are 100% accurate so you do not under/over dose the mg/ml.



Be sure you are heating your gear up b4 inj.

Be sure to heat the area you are injecting to.

Be sure to sterilize where you are injecting

Use a new needle to inject from what you use to pull the gear

Use a heating pack on that leg.

 

[h4x0l2]

If you have a fever, you may need to go into the ER.

 

[CABO JO]

How much are you pinning?

What type of gear.Test 250mg???

Size a length of pin?

Pre pin routine?

You have way to much pain.

 

[AnabolicLove]

Damn dude.. I'm on my first cycle too. I've pinned 11 times so far, with very little to no pain what so ever. I even use 22 gauge needles, and I stick to my thighs because of how easy it is to do myself. I've even used two different brands of gear and I get almost no soreness at all!

 

[aitheanswer2k4]

h4x0l2 ya i do everything you said unless by heating you mean boiling? Except for the sterile oil.

 

[h4x0l2]

Generally you want to get it to about 200 degrees. Let it cool so its above room temperature, but you can hold it in your hand without it hurting. That just re-steralizes the oil. You want all the oils sterile.

 

[aitheanswer2k4]

CABO JO for your question :

How much are you pinning? 250mg

What type of gear.Test 250mg??? ya 250mg of test c from z-line

Size a length of pin? 25g 1'

Pre pin routine? wash my hands,heat the vial, then swab the top of rubber stopper with pad, then pull how much air am going to inj. in the vial, push the air in the vial, then pull the plunger back using the 21g to pull the test to 1cc in the syringe, switch needles to inject with my 25g 1' needle. (usually take about 30 seconds to inject i try to inject slowly.)

 

[aitheanswer2k4]

h4x0l2 I heard not to boil your test because it might fail and turn cloudy? idk though thats just what i have heard from forums. (are i might understood your post do you mean do that with the vial i got now? or you mean do that with the when you cut the oils with usp sterile oils??)

 

[h4x0l2]

It can crystallize, that's why to keep it around 200. You don't leave it in long

 

[h4x0l2]

h4x0l2 I heard not to boil your test because it might fail and turn cloudy? idk though thats just what i have heard from forums. (are i might understood your post do you mean do that with the vial i got now? or you mean do that with the when you cut the oils with usp sterile oils??)

When you cut them is correct.

 

[aitheanswer2k4]

Oh ok i thought you meant doing that to just the vial i got now

 

[aitheanswer2k4]

I thought i seen where someone said he already cuts his products with eo oil though. I could be wrong but i thought i seen that on this forum. So if he does cut them with eo oil will it be safe to still cut then to with another oil?

 

[CABO JO]

CABO JO for your question :

How much are you pinning? 250mg

What type of gear.Test 250mg??? ya 250mg of test c from z-line

Size a length of pin? 25g 1'

Pre pin routine? wash my hands,heat the vial, then swab the top of rubber stopper with pad, then pull how much air am going to inj. in the vial, push the air in the vial, then pull the plunger back using the 21g to pull the test to 1cc in the syringe, switch needles to inject with my 25g 1' needle. (usually take about 30 seconds to inject i try to inject slowly.)

Your routine looks good.I'm sure you swab the area you inject.Make sure you hit the glutes with 1.5" pin.Not sure about steralizing the product, don't think I would do that.Might go back to the source and ask him.UGL can be hit and miss.Good luck

 

[h4x0l2]

It wouldnt matter as long as the doses are match and it is sterile. Might get thick though.

 

[aitheanswer2k4]

well like everyone says uncle is def. legit so i know it cant be the product, hopefully not anyways. Just didnt know it would hurt this bad. Why a 1.5' in the glute? i was told on the boards that 1' would do if your low body fat mine is around 6 to 8%.

 

[aitheanswer2k4]

so h4x0l2 you basically mean if i do 1cc of 250mg of my test i need to do 1cc of the sterile oil?

 

[h4x0l2]

No... I didn't post that right. The idea is to make sure you measure out everything exact so you know the ratio mg/ml.

 

[aitheanswer2k4]

ok that sounds very confusing. Guess am just going to have to fight through the pain. Could i not just buy some usp sterile oil already filtered and sterile just going to say its from research supply where i would get it from. Why couldn't i just buy the 5ml Filtered Cottonseed Oil and then put that into a separate vial. Then just get 1cc of that then 1cc of my test? (sorry i have researched steroids for along time! Just never researched how to cut them with oils because i thought i would never have this problem. Just dont want to sound stupid here.)

 

[C Wood]

If this is your first cycle you'll learn where to inject and where not to inject.Unfortunately it can be painful to learn where those spots are.I had severe injection site pain when I started out.I've found the biggest problem was poor location and a rookie holding the rig.

For example if I pin my quads in the correct spot I have no pain at all with 400mg/ml test E.If I go one inch lower I will limp around for 4 to 5 days because of the pain.