What were your steps in making it? You might not have fully brought the hormone into solution before adding oil. Do you use a thermometer throughout the process?
Powder still good?
- Thread starter Infantry87
- Start date
What were your steps in making it? You might not have fully brought the hormone into solution before adding oil. Do you use a thermometer throughout the process?
Pinnacle@Rep
Muscles can't stop this..
I always keep my raws in the freezer!!! Oxidation happens quicker at warmer temps!!! If kept in the freezer they will last MUCH longer than at room temp!!!
Secondly, If your test has particulates settling then I suggest you retest your Test E again as Test E always has a very distinct Piney fruity smell!!!!!
The Test E is VERY VERY hard to make crash, so if it is crashing then there is a major problem somewhere and you will have to first CONFIRM that you know the substance IS IN FACT TEST E!!!!
Then at that point you will need to run down your exact process step by step including your Exact heat, length of heat, filter type and temp during filtering, EVERYTHING cause Test almost can convert with no heat!!! How was your stirring? What steps did you take when adding your wets and powder? What temp when added? Quantities you used with all your wets and your powder???
Secondly, If your test has particulates settling then I suggest you retest your Test E again as Test E always has a very distinct Piney fruity smell!!!!!
The Test E is VERY VERY hard to make crash, so if it is crashing then there is a major problem somewhere and you will have to first CONFIRM that you know the substance IS IN FACT TEST E!!!!
Then at that point you will need to run down your exact process step by step including your Exact heat, length of heat, filter type and temp during filtering, EVERYTHING cause Test almost can convert with no heat!!! How was your stirring? What steps did you take when adding your wets and powder? What temp when added? Quantities you used with all your wets and your powder???
Infantry87
New member
Yea I used bottle tops. Shit still killed my thumb though. Next time I'll use a caulk gun I've heard of some dudes doing that so I should try it.
No bro I didnt use a therm but I shouldve. I used RJ's recipe for the suspension. The only thing that fucked me up a little bit was when I was filtering the test through the filter into the bac water and it instantly crashed to the bottom. But after all was finished i put it on the stove top and shaked the shit outta it even more and longer and it seemed to come back. I plan on warming it up before everyday injections to be on the safe side and make sure im getting the correct amount of dosage and hormone
Infantry87
New member
Thats bro. the test e was extremely fruity and piney. the test e was the easy one ive made it once before but the suspension wasnt bad but still a pain in the ass. I followed exact guidelines to RJ's recipe for the suspension and it seemed to work well
Infantry87
New member
the base was micronized and the test e was fine. it's the base where the yellow shit keeps settling at the bottom at the vial but when i heat it up its fine
Infantry87
New member
ok so i did my 3rd shot of this homebrew and it honestly feels like i was dead legged by the hulk. I did 2/20 ba/bb 100mls/250mg/ml. Whats going on with my homebrew?
crazyfmike
New member
Did you make a blend of base and E ??
Infantry87
New member
No I made 100mls of Test E and Deca @ 250mg/ml and made 30 mls of test suspension @100mg/ml. The test e and deca are fucking me up bro. Pain that last 4/5 days idk whats going on. Did everything to the T man
crazyfmike
New member
crazyfmike
New member
First thing that comes to mind is reversed BA and BB....that will hurt like a MFer!
The "crashing" is not consistent with reversed solvents . . . just talking out loud to get all this in perspective.
The Test E is 250mg/ml?
Deca is how many mgs and in it's own vail at ??? mg/ml
The "crashing" is not consistent with reversed solvents . . . just talking out loud to get all this in perspective.
The Test E is 250mg/ml?
Deca is how many mgs and in it's own vail at ??? mg/ml
Infantry87
New member
Test E 250/ml and same for deca. Both are in its own seperate vials. Only thing i can think of is maybe i shouldve baked the finished product???
Baking does absolutely nothing. If you brought your raw into solution with the solvents and heat then there's no need.
Test E and nandro should not be painful at 250ml/ml. What was your break down of raws and solvents? I know 2/20, but I want numbers and grams.
Gear should be smooth at that dose.
Test E and nandro should not be painful at 250ml/ml. What was your break down of raws and solvents? I know 2/20, but I want numbers and grams.
Gear should be smooth at that dose.
Infantry87
New member
Heres my steps:
Used a 500ml beaker and put 25.00 grams of enanthate powder and put in the beaker.Did the same amount of grams with the deca too
Placed the 2ml of BA and the 20ml of BB in there
put a frying pan on the stove top at heat level 3 or so. Placed the beaker with ba/bb/powder in the pan and let the pan heat up the beaker. Saw the powder start to “melt” or dissolve
ba/bb has dissolved the powder, poured in the oil (59.25ml total, added 55.25ml and saved the other 4ml oil to run thru syringe filter after all test is filtered to purge filter of all test
turned down the heat to 1 or so for the mixture to stay warm
Placed a 18g needle through the rubber stopper and into a 100ml bottle Put the .45 whatman filter on top of the needles just as in a fina conversion. Also put a 20-23g needle thru stopper as a vent.
Used a 10ml syringe to draw out the warm oil, push the oil through the whatman filter and into the sterile glass vial
Infantry87
New member
Everything was extremly sterile using alcohol numerous times and also baked the vials and beakers @ 350 for 35 minutes. I've been told its the .45 filter and shouldve gone with the .22 to better filter out the results.
Your break down looks good. Lots of people use .45 micron and i've never heard complaints of that but then again I only use .2 micron.
Test ennthate's powder weight is .85 which will bring you to correct oil volume of 56.25ml but that isn't going to make a difference in this situation. Make sure on larger batches that you don't use the universal powder weight of .75 as you'll come out over or under.
I'm really not sure why it'd be causing pain, could be your raws and impurities.
Test ennthate's powder weight is .85 which will bring you to correct oil volume of 56.25ml but that isn't going to make a difference in this situation. Make sure on larger batches that you don't use the universal powder weight of .75 as you'll come out over or under.
I'm really not sure why it'd be causing pain, could be your raws and impurities.
Infantry87
New member
Source was checked thru here and was legit when I ordered but you still never know. Everything melted around the temps they were supposed too. Im gonna start using .2 and see how that works and make a smaller batch around 30ml. Shits annoying bro good thing i have backup vials
Infantry87
New member
Honestly bro I'm not gonna lie. I didnt check it. Stupid but I know I shouldve. What shouldve it been ?
gizmo201111
New member
View attachment 546308 think we got same supplier . did your powders end up being legit?
