please help guys im a complete moron

[bignewf]

so I opened my new vial of t300, pumped to try this stuff out, and managed somehow to pull the metal ring off as well.
me being me I figured no big deal the rubber stopper is in there good and solid so I pumped 0.5ml of air into the vial tipped the vial upside down and proceeded to pull the plunger.

well the rubber stopper immediately come out so in a panic I jammed it back in pulled the syringe out and was like o fuck what do I do now.
so I fully loaded two syringes.

I now have 6 ml ( so 4ml wasted) of t300 in 2 syringes and don't know what to do

I have an empty test-e vial that I finished on Thursday. can I just pump it into that and draw as needed, or should I leave it in the syringes and use it from that...

or is the gear competly wasted.. please help guys.. I hope its not wasted.. this is all I have until my order gets in for my oct bulk.. it was I vial I had left and was using to cruise into my bulk.. now if its still good I have just enough left

any help will be greatly appreciated thanks

 

[00pmac00]

First of all...LOL, it went from bad to shit, quick it seems

I would see no harm in putting the two syringes into the recently emptied vial. But I would only question the sterility of it since you drew the contents after exposing the contents to air. Odds are nothing is wrong though, but there is still a small chance I guess.
Probably nothing to worry about, but I would heat the vial on the stove in boiling water for a bit.

 

[3J]

yup... looks like sterility is going to be the big issue here...

i personally would cut my losses and move on

 

[SamSport]

you could do that. but, sterility issues. your call

 

[Nightmare007]

Cut your losses and move on or risk infection

 

[bignewf]

if I heated up the vial in boiling water and put the oil in the hot vial and kept it in the water for a little bit would this help with sterility issues??

I can get another vial by the end of the week but id miss 3 shots because of it

 

[enzo321]

if I heated up the vial in boiling water and put the oil in the hot vial and kept it in the water for a little bit would this help with sterility issues??

I can get another vial by the end of the week but id miss 3 shots because of it

That would probably kill everything, but it would need to be at a boil. That wouldn't remove large contaminants like dirt, or debris.

 

[bignewf]

theres nothing in it.. the stopper just popped out long far enough for the oil to leak past before I could put it back in... im just concerned about contamination due to air access

 

[3J]

theres nothing in it.. the stopper just popped out long far enough for the oil to leak past before I could put it back in... im just concerned about contamination due to air access

that would be the main concern actually

 

[clman8585]

Put it in the micky-wave and then filter itwith watman paper and reseal

 

[clman8585]

Always make sure you have some fish-flex handy!

 

[enzo321]

I would maybe try throwing the stuff in your empty vial and boiling some water.

Like this..

1)boil water
2)Submerge vial into water for 60secs
3)Take out for 30 secs
4) submerge for another 60 secs.
etc...

And I would do this for a total of 10 minutes. Do not put it by anything cold or the glass with explode.

 

[enzo321]

Put it in the micky-wave and then filter itwith watman paper and reseal

The glass would explode in a micro wave far to easily. at least it sounds more dangerous.

 

[jkr2020788]

I think you'll be fine as long as nothing hit it. People might say the air will contaminate it, but we inject 1ml of air into the vial everytime we draw. That same "unsterile air" is now in the vial. I've never had a problem with infection. I think ud be fine puttin it into a clean vial. I would just be sure you have enough test to finish your cycle now tho lol.

 

[enzo321]

I think you'll be fine as long as nothing hit it. People might say the air will contaminate it, but we inject 1ml of air into the vial everytime we draw. That same "unsterile air" is now in the vial. I've never had a problem with infection. I think ud be fine puttin it into a clean vial. I would just be sure you have enough test to finish your cycle now tho lol.

True there is a sense of analness in this discussion

 

[bignewf]

Yea I got enough until I start blast in October.

 

[DreDay187]

The benzyl alcohol content, if at least 1% should be enough to keep the solution sterile (provided nothing else came in contact with it or got mixed in besides air). Exposure to air will technically make it un-sterile but again the BA should be plenty (if above 1%) to keep sterility. Just in case I would get a .22 um whattman syringe filter or a millipore filter and vacuum pump and pass it through the filter to remove any contaminants.

 

[clman8585]

^fuck buying a pump so save 6ml of gear

 

[DreDay187]

^fuck buying a pump so save 6ml of gear

For 6ml of gear, yea I'd agree. For me though, who wants to home brew for my next cycle, ill def look into a pump instead of the normal syringe filters. Saves a lot of time.

 

[clman8585]

Yea I def see homebrewing in my near future.