Why does T400 hurt so bad?

[856crs]

Even though I'm a newbie ive been reading a lot on t4 and everyone says the same either mix it with other juice or take the pain. I can say that personally my ass feels like it was hit with a sledgehammer. Felt great about an hour afterwards but two to three I went to stand up and it killed. Try warming it up and rubbbbnbbbnbb the area before and after you inject. And these pain relieving alcohol whipes helped a little. You can also try half a dose in each shoulder or each cheek split it up half a mil two times a week even still works out to 1 mil a week. Good luck I'll let you know if anything works for me

 

[856crs]

IMO,, It's not so bad just the first pin then the second in the same spot it goes away much easier..

Stupid question. But you're saying inject in the same spot for the second week? Is that cool for all the following weeks too because I'm thinking I should switch it up but who knows it's my first cycle

 

[Die$eL~Man]

its the ba content on the higher mgs

 

[C-Dub]

Im going threw the same pain right now! Im on week 7 of Test400 12ml and every shot has hurt just as bad. This week i tried putting a half ML in each butt cheek and its still rough! I run it under hot water for like 10min's before sticking, which helped but still painful. So, i have a question for the vet's...i also have a bottle of test 250, which doesn't hurt at all, that i stack with the 400 (1ml of 400 on Monday an 1ml of 250 on Wed). Should i try mixing them to together? How much of the 250 would it take to dilute the 400? 1ml of 250 and half ml of 400? I have 4ml of T400 left and i think 6ml of 250....

 

[Pinnacle@Rep]

i was running syntrop 450 and let me tell you that fn hurt. the first shot of that was like being hit with a burning hot poker.
the BA is higher to pull that much test into 1ml. but i stopped trying to slam a full ml and dropped it back to a half ml and worked it back up over a few weeks. i got use to it and it was fine there after.

The BA isn't higher in 400 to hold it in solution. It would be the BB.... BA is used as a preservative to inhibit the growth of bacteria in the vial. 2% or 3% BA in a vial is plenty and that is the same for 250 test or 400. It is the amount of BB used that is different. 0-15% BB used with Enanthate to hold 250 in solution but I use 20% BB to hold 400 in solution.
The reason for the burn is not the Chemicals used BB or BA, the reason is the super saturated concentration of Test powders crammed into one little vial! This is just so much in one area that the body's inflammation reaction takes over and is forming an abscess around the compound because it is in too concentrated of a dose! Adding the deca (which is not as reactive to the body's inflammation process) dilutes the solution of test down to a bearable level.
You can take 1cc of the 400 and draw it up into a pin and then 3/4 cc of GSO (sterile) and run it under hot water for a bit, flick it around and then pin it and you will be fine but you might as well be buying two bottles of test 200 and shooting 2cc a shot..... same thing!!!
Test 400 is for ppl whose bodies have become resistant to extreme doses of test per week and even still then, alot of guys experience knots and inflammation.

Chemist

 

[kountrystrong]

i have done supertest 450 and that was a bitch anywhere i shot it,but the slower i did the injection the better the pain was ,and i tried every trick in the book to help me and that was the best advice anyone gave me that actually worked for me and i was doing 900mgs a week 1cc on mon and one on thur. and the injection would take like 3 or 4 min but it helped with the pain and with those softball size knots i was getting

 

[maplestring]

The BA isn't higher in 400 to hold it in solution. It would be the BB.... BA is used as a preservative to inhibit the growth of bacteria in the vial. 2% or 3% BA in a vial is plenty and that is the same for 250 test or 400. It is the amount of BB used that is different. 0-15% BB used with Enanthate to hold 250 in solution but I use 20% BB to hold 400 in solution.
The reason for the burn is not the Chemicals used BB or BA, the reason is the super saturated concentration of Test powders crammed into one little vial! This is just so much in one area that the body's inflammation reaction takes over and is forming an abscess around the compound because it is in too concentrated of a dose! Adding the deca (which is not as reactive to the body's inflammation process) dilutes the solution of test down to a bearable level.
You can take 1cc of the 400 and draw it up into a pin and then 3/4 cc of GSO (sterile) and run it under hot water for a bit, flick it around and then pin it and you will be fine but you might as well be buying two bottles of test 200 and shooting 2cc a shot..... same thing!!!
Test 400 is for ppl whose bodies have become resistant to extreme doses of test per week and even still then, alot of guys experience knots and inflammation.

Chemist

the concentration is high.. but thats not the problem! if it burns like hell its because you have alot of alchol in the injection! doesnt take a chemist to understand that alchol is the most sterile thing they can use to fuse the concentrations together.

 

[Trust_]

AML's T400 is smooth as butter.. doesnt hurt at all... However, if it gets cold, it will instantly crash..its the only downside to it.

 

[barrysanders]

huh, ive been using t400 for about 2 months now and I dont notice a diff.. and i do ED injections. Lucky me I guess

 

[josephblow]

1200mg test? 900mg deca?

Dude cut that in half. If you don't know much to take then you should never take it blindly. Hope you know about pct.

 

[Strong Man]

Well you think T400 hurts then try Test 500! It feels like a mule kicked me in my ass, lol....I have to say that the pip is getting better each week as I just started my cycle 30 days ago.