Slin pin method---for those interested

Italiano I don't doubt you and really want to try this but how hard is it to push oil through a slin pin? I use 25g x 1" for my full rotation and if I don't preheat the oil it is very hard to push the shot out of the syringe. Also how much do you load in one shot. I have small hands and would really have a shaky hand if the plunger was backed all the way out.
 
That's what I'm having problem with. Loading 1cc the plunger is hard to control because the oil starts coming out once u try to put it back in the syringe. I bent the slin pin yesterday doing my delt. I thought it was going to break off in my shoulder. The needles on slin pins are very easy to bend so it scared the shit out of me
 
MightyMouse9999 said:
That's what I'm having problem with. Loading 1cc the plunger is hard to control because the oil starts coming out once u try to put it back in the syringe. I bent the slin pin yesterday doing my delt. I thought it was going to break off in my shoulder. The needles on slin pins are very easy to bend so it scared the shit out of me
Click to expand...

Not good.
That would be bad news bears.
 
WolfsLair said:
Italiano I don't doubt you and really want to try this but how hard is it to push oil through a slin pin? I use 25g x 1" for my full rotation and if I don't preheat the oil it is very hard to push the shot out of the syringe. Also how much do you load in one shot. I have small hands and would really have a shaky hand if the plunger was backed all the way out.
Click to expand...

Bro, I don't try this...I use it ALL THE TIME with every cycle I do. Surprisingly enough, the oil pushes through just fine. Slins only hold 1CC so figure it out accordinly. Draw with 18g or 20g and fill the slin and replace plunger and you are good to go. I've had zero problems since I've started doing my injects this way.
 
MightyMouse9999 said:
That's what I'm having problem with. Loading 1cc the plunger is hard to control because the oil starts coming out once u try to put it back in the syringe. I bent the slin pin yesterday doing my delt. I thought it was going to break off in my shoulder. The needles on slin pins are very easy to bend so it scared the shit out of me
Click to expand...

After you transfer oil to slin pin, put plunger in just far enough to seal it and then turn it upsidedown until the air goes to the top towards the needle. After all the air goes up, push the excess air out of the slin and you'll be all set. You shouldn't have any issues with oil coming out. I've never had that problem.
 
hey Italiano Going to try this method i have a 0.33mm (29g)x12.7mm) Slin pin.

How long does it usually take to inject ?

What gear have you used this method with ?

Running GP Test E Thinking ts going to take around 1 min to inject it pre heated ?
 
blazeftp said:
hey Italiano Going to try this method i have a 0.33mm (29g)x12.7mm) Slin pin.

How long does it usually take to inject ?

What gear have you used this method with ?

Running GP Test E Thinking ts going to take around 1 min to inject it pre heated ?
Click to expand...

I've used Tren, Test E, Deca and NPP with a slin. It won't take you a minute. I'd be very surprised if it did. It takes me maybe 20-30 seconds. I've never timed it but just guessing.
 
i will give it a go myself but i take like 3-4 ml thats going to be a lot of pins.
and what the guy on the vid pulled up was water based B12.
did i miss how long the shot takes with oil.
 
You must log in or register to reply here.

Similar threads

M
Erectile Dysfunction on Test Only Blast & Cruise? Bad Gear? Blood Work?
Replies
10
Views
2K
casanovaaa
casanovaaa
O
Cancer survivor looking for advice
Replies
4
Views
2K
Mycelium
Mycelium
B
Ready for a BLAST after summer
Replies
16
Views
1K
BakedGoods
B
Harnold
My deca sides or not? Any opinions on this?
2
Replies
21
Views
2K
Harnold
Harnold
S
New member here. Wanted to say that you guys are awesome.
Replies
3
Views
2K
Nicky_eye_lids
Nicky_eye_lids
Back
Top